 Lindberg/Blue M* 1500°C Heavy Duty Independent Control Tube Furnaces
|
|
CC58125BC CC58125C CC58125PBC CC58125PC CC584753PBC CC58475C CC58475PBC CC58475PC CC584853PBC CC58485C CC58485PBC CC58485PC STF54233C STF54453C STF54459C STF54759C STF54779C
Heavy duty 1500°C tube furnaces are available in single and three zone models, designed for high temperature metallurgical, ceramic, chemical and electronic research.
Features
Double-end silicon carbide heating elements mounted above and below the chamber.
Heating elements with unique right angle bend, sidewall mounting and compressed spacing at ends deliver fast heatup and recovery and offset heat loss from end of process tube.
Removable side panels for easy installation and electrical connection, simplified heating element replacement and adjustment.
High temperature insulation with insulated end vestibules for better uniformity and energy efficiency.
Long life, fast response type “R” thermo-couples with 10' compensated lead wire and polarized plug.
Applications
Annealing.
Crystal Growing.
Calibration.
Heat Treating.
Three Zone Models
Three independent power circuits (zones) with independent thermocouples for control references.
Full adjustment of each zone over entire operating range of 500°C to 1500°C.
Center zone uniformity achieved and operating length maximized through adjustable profiling of end zones by independent controller.
Controlled temperature uniformity achieved with independent setpoint of end zones higher or lower than center zone.
Single Zone
1500°C Digital, Single Setpoint Controller
Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack.
Includes microprocessor-based PID control (proportional, integral, derivative), single segment, single setpoint, 1 ramp to setpoint.
Built-in adjustable high limit overtemperature protection.
Simultaneous LED display of actual temperature vs. setpoint.
May be configured to display temperature in either °C or °F.
1500°C Digital Single Program, Multiple Segment Programmable Controller
Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack.
Includes microprocessorbased PID control (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control. for more information.
Built-in adjustable high limit overtemperature protection.
Simultaneous LED display of actual temperature vs. setpoint.
May be configured to display temperature in either °C or °F.
Option B Overtemperature Control (OTC)
Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
Protects furnace and load in the event of primary control circuit failure.
Overrides main controller and shuts off power to furnace if high limit is reached.
Manual re-set required for safety.
Operates via magnetic contacts through signal from independent thermocouple.
Optional RS485 Digital Communications Port
RS485 Digital communications port available as an option.
Allows controller to be connected to a PC for remote monitoring and control of the furnace.
Up to 30 units can be connected to one PC.
Three Zone
1200°C Three Zone Controller
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
Includes three microprocessorbased PID controls (proportional, integral, derivative), single segment, single setpoint, 1 ramp to setpoint.
Built-in adjustable high limit overtemperature protection.
Simultaneous LED display of actual temperature vs. setpoint.
May be configured to display temperature in either °C or °F.
1500°C Three Zone Single Program, Multiple Segment Programmable Controller for Center Zone
Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
Center Zone
One microprocessor-based PID programmable control (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control.
Built-in adjustable high limit overtemperature protection.
Simultaneous LED display of actual temperature vs. setpoint.
End Zones
Two microprocessor-based PID control (proportional, integral, derivative), single segment, single setpoint which mimic the programmed profile of the center zone controller, but allow an offset up to 100°C (+/- 50°C).
Offset is LED displayed.
Option B Overtemperature Control (OTC)
Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
Protects furnace and load in the event of primary control circuit failure.
Overrides main controller, and shuts off power to furnace if high limit is reached.
Manual re-set required for safety.
Operates via magnetic contacts through signal from independent thermocouple.
Optional RS485 Digital Communications Port
RS485 Digital communications port available as an option.
Allows controller to be connected to a PC for remote monitoring and control of the furnace.
Up to 30 units can be connected to one PC.
1500°C Three Zone Single Program, Multiple Segment Programmable Controllers
Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
Includes three microprocessor-based PID programmable controllers (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control.
Built-in adjustable high limit overtemperature protection.
Simultaneous LED display of actual temperature vs. setpoint.
May be configured to display temperature in either °C or °F.
Option B Overtemperature Control (OTC)
Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
Protects furnace and load in the event of primary control circuit failure.
Overrides main controller and shuts off power to furnace if high limit is reached.
Manual re-set required for safety.
Operates via magnetic contacts through signal from independent thermocouple.
| QTY |
PRODUCT DESCRIPTION |
OUR PRICE |
| |
all prices shown are in USD
|
|
|
|
STF54453C-EA
Lindberg/Blue M* 1500°C heavy duty independent control tube furnace, 1 zone, 208/240v, 50/60hz, 6857w
|
$8,153.20
$9,592.00 |
|
|
STF54233C-EA
Lindberg/Blue M* 1500°C heavy duty independent control tube furnace, 1 zone, 208/240v, 50/60hz, 7200w
|
$6,613.85
$7,781.00 |
|
|
STF54459C-EA
Lindberg/Blue M* 1500°C heavy duty independent control tube furnace, 3 zone, 208/240v, 50/60hz, 12600w
|
$13,790.40
$16,224.00 |
|
|
STF54759C-EA
Lindberg/Blue M* 1500°C heavy duty independent control tube furnace, 3 zone, 208/240v, 50/60hz, 20000w
|
$18,273.30
$21,498.00 |
|
|
STF54779C-EA
Lindberg/Blue M* 1500°C heavy duty independent control tube furnace, 3 zone, 208/240v, 50/60hz, 25000w
|
$19,386.80
$22,808.00 |
|
|
CC58485C-EA
Lindberg/Blue M* controller, digital, 208/240v, 50/60hz, 60/120/60a
|
$8,088.60
$9,516.00 |
|
|
CC58125C-EA
Lindberg/Blue M* controller, digital, 208/240v, 50/60hz, 60a
|
$2,555.10
$3,006.00 |
|
|
CC58125PBC-EA
Lindberg/Blue M* controller, digital/overtemp control/prog, 208/240v, 50/60hz, 60a
|
$4,499.90
$5,294.00 |
|
|
CC58485PC-EA
Lindberg/Blue M* controller, digital/prog, 208/240v, 50/60hz, 60/120/60a
|
$8,675.10
$10,206.00 |
|
|
CC58125PC-EA
Lindberg/Blue M* controller, digital/prog, 208/240v, 50/60hz, 60a
|
$3,276.75
$3,855.00 |
|
|
CC584753PBC-EA
Lindberg/Blue M* controller, digital/prog/overtemp control, 208/240v, 50/60hz, 30/60/30a
|
$10,517.05
$12,373.00 |
|
|
CC58485PBC-EA
Lindberg/Blue M* controller, digital/prog/overtemp control, 208/240v, 50/60hz, 60/120/60a
|
$9,865.95
$11,607.00 |
|
|
|
|
 |